How To Clean A K & N Air Filter

Cleaning your AK-47? Only it'south so rugged, and…Russian.

Despite the ruggedness of your AK-47 and its renowned power to function with sand, grunge, and grit choking its internals, basic cleaning and maintenance program volition certainly extend the life of your equipment.

This is a quick guide on AK-47 Cleaning and Maintenance!

AK-47 Cleaning and Maintenance

Many dissimilar methods of cleaning your AK-47 blazon rifle are discussed among AK fans.

Methods are really diverse, and unlike whatsoever other blazon of war machine weapon include terms like "water hose", "dishwasher" and "local car launder". Seriously.

The rugged design of the AK-47 and its inherent simplicity let its maintenance to be discussed in such words. It is a compliment to a military rifle designer to have upkeep of his design discussed in terms like 30 weight motor oil and bearing grease- both viable options with the AK-47!

1) Cleaning Products (Selection-n-choose)

CLP BreakFree – "CLP Breakfree" is the stuff yous hear discussed almost of the fourth dimension in armed services rifle circles. This stuff is amazing, and so they say.

Since I've never had trouble with my guns afterward using this stuff, I would have to agree. CLP stands for Clean-Lubricate-Preserve. It has a lubricating teflon ingredient and is a superb solution for all bones gun needs. It was adult for the Us military and is marketed to the public.

Gun Scrubber Ak-47

Gunscrubber or Brake Cleaner – This stuff is an aerosol, loftier-pressure cleaner. Information technology cuts grease and carbon and evaporates to leave bare, dry out metallic. Information technology will attack many plastics, wood finishes and pigment, and so test information technology outset. Use eye protection- the high-pressure level jet stream will rebound off of corners and flat surfaces and blind you.

Go outside too- the fumes volition knock yous back to third form. I wear gloves, for this stuff is a carcinogen and probably much more than. If it gets under a ring on your finger you lot volition feel it for days.

Now, all that said, this is the easiest and near effective way to degrease a gun. It cuts through most carbon deposits also. The downside- if the health risks weren't enough, are that it is expensive.

Gunscrubber is a bit costlier than restriction cleaner, but check local prices every bit they may vary. One can disappear quicker than you expect. Some folks utilise Carb cleaner. Carb cleaner is a much more aggressive solvent and leaves a slight lubricant behind. In a pinch, information technology will substitute for restriction cleaner, but information technology isn't recommended.

Calorie-free Gun Oil – This is thebasic automobile oil we are all familiar with. Information technology's bully for general protection of all metal surfaces. Light gun oil can be used on bare wood in a pinch.
Pulverization Solvent – Hoppes No. 9 comes to mind equally the most common brand. This stuff is proficient for cleaning the bore of powder balance and carbon buildup. If you have guns at all, you lot probably have some of this stuff.
Heavy Grease – Any type of heavy lubricating grease works well on an AK-47, though synthetic grease with Teflon additives or lithium blazon grease works all-time. I use Tetra Grease, a make of synthetic white grease.

motor oil for AK-47

Motor Oil – Yep, Motor Oil. Use oils that have no additives like Mobil 1 synthetic. Really, Bushmaster recommends motor oil for the outside of their AR-fifteen rifles, but only non-detergent.

Detergent oils and oil additives are specifically NOT recommended because they may degrade the clear sealant Bushmaster applies over the phosphate terminate. I doubt if many AK-47s have this clear sealant, however. Motor oil volition work as a full general overall lube, fifty-fifty on the commodities-carrier track.

Automatic Transmission Fluid – ATF is a basic oil, it has fewer additives than motor oil and is used with great results as a general lubricant by many AK-47 owners. Its like the poor comrade'southward CLP and for lubing an AK-47, it seems plumbing fixtures that ATF is RED
WD-40 – WD-forty stands for "water displacement #40", and is a fine full general-purpose solvent. There are ii schools of thought about WD-40. Some swear by it, claiming information technology is great equally a cleaner and protector, merely that it should never be used for lubrication.

The other schoolhouse says "WD-40 will never touch my guns!". That's because it leaves a remainder behind that becomes sticky and gummy with age. If WD-forty is allowed to pool up in corners and crevices (around firing pins?) it tin cause parts to stick.

I personally utilize it equally a flushing agent, only don't rely on it for rust protection as it is non designed for long term protection. As a h2o displacement product, it drives water out of the gun, but that'southward where its effectiveness to the gun possessor ends, especially in humid climates.

Bore brush AK-47

Bore Brushes – Get some. Bronze or brass is best to go the garbage out of the rifling grooves. Bore solvents similar Hoppes only practice so much on stubborn gunk.
Sleeping room Brushes – Brass bristle chamber brush for scrubbing out the receiver and sleeping room is a necessity. A toothbrush will suffice in nearly cases.
12 judge bore brush – Go a brass or statuary 1 for cleaning your gas tube. Make certain you lot have a shotgun cleaning rod to attach it to every bit it will not fit on your rifle cleaning rod.
Bore Patches/Rod – Demand I say this? If you have no cleaning rod and don't know what I'm talking nearly, sell your guns. I discover the AK rod is not the tool I want sliding down my rifle'due south bore- its besides hard! I use a cheap aluminum rod from those cleaning kits. Patches need to be small enough to move through the bore, but not so tight that you lot curve your rod. Utilize .30 caliber patches or cutting a tee shirt into i″x2″ rectangles.
Unproblematic Greenish – This h2o-based, biodegradable degreasing cleaner is not bad for gun owners who don't similar the noxious chemicals we normally use. With a toothbrush, Simple Greenish is great stuff. Dry out your gun parts in the oven for xxx minutes of so after using any water-based production or you may find rust forming overnight.

ii) Field stripping the AK-47

Before you lot beginning field strip your gun only exist sure information technology'due south unloaded- bank check information technology! Every gun is loaded!

Remove the top cover off of the receiver by pushing the button on the rear of the receiver embrace and lifting the cover-up.
After the cover is removed, slide the receiver servant button that held the receiver cover down forward until information technology disengages from the trunion that holds it in identify.
This will allow you to slide the recoil spring out of the bolt carrier.
Next, pull back the bolt to the rearmost position and lift the bolt carrier/gas piston assembly out of the receiver. Spotter the bolt! It is loose and with a turn volition fall out.
Remove it by turning information technology until the locking tab is clear and you can slide information technology forward and free.
Finally, with the bolt carrier/gas piston associates removed, lift the lever on the right side of the gas block up by rotating it clockwise.
The gas tube/upper hand guard assembly volition be loose now and you can move it upwards and off the gun.

That's all that is required to field strip your AK-47, and it is gear up for cleaning.

ak-47 field strip

3) Initial Cleaning

Beginning, I utilise CLP to the parts that I tin can become at with a toothbrush and scrub., This includes the commodities carrier/gas piston and the bolt itself. I as well use Hoppes #nine on the diameter by passing a saturated patch down the barrel. You lot can utilize whatever solvent here that yous wish, from kerosene to WD-40.

The idea is to flush out the grunge and scrub off the stubborn carbon deposits. The brass brushes volition come up in handy on the gas piston and the bolt face. Run the shotgun castor down the gas tube a few times to knock out any carbon in at that place. Check the gas port too, making sure the channel leading to the barrel is open and costless of carbon. A special tool is available for this, or a length of glaze hangar will substitute just fine.

4) Degreasing

Once I've loosened the really nasty grunge with the toothbrush and flushed with cleaner of my option, I spray off the interior, parts and diameter with brake cleaner to go the cleaner and remainder of the grunge off. This pace leaves a overnice, greaseless, bare metal terminate.

5) Lubrication

Using CLP, I lube all operating parts. Within the receiver, get alee and coat the whole thing in a low-cal film of CLP or light machine/gun oil. You don't want whatever rust in there! I use Tetra grease on the track. I give it a good coat with my finger, but it actually doesn't need much as this stuff leaves a film behind fifty-fifty if y'all tin can't see information technology. A big blob of grease just attracts dirt.

AK-47 lubricate

half-dozen) Protection and Storage

Employ CLP here. Some folks prefer Motor oil, Automated Manual Fluid, or calorie-free gun oil. With a rag, wipe downward all exposed metallic with CLP- interior and exterior, parkerized, blued or otherwise. Get information technology all. A slight flick is all that is required to protect the gun.

And that'southward it!

Alternate cleaning methods for the AK-47

Field strip, run the water hose through it, dry in sun, squirt with motor oil, reassemble.
Field strip, put in dishwasher, run bike, dry in over at 250 degrees (without stocks of course), squirt with motor oil, reassemble.
Hose down the whole thing with the local machine launder pressure washer. Stick on radio antenna to dry out while driving home. Dip in motor oil. Store.

Sound insane? These are all methods people accept actually used! I use the dishwasher when I really want to degrease a gun. To prep my SAR-1 for refinishing I had to remove all grease and lubricants inside and out. I used gun scrubber gets the initial layers of grease/oil off, then heated the metal parts in the oven for a while to bulldoze the grease out of the tight spots and from between the stampings and metal-to-metal areas.

I'd then concentrate on that area with acetone and a brush. I repeated the process a couple of times until I had removed equally much grease and oil as humanly possible. Once washed, in the dishwasher information technology went, broken downward of course. When the dry cycle was over, I put it back in the over to bulldoze out leftover moisture then proceeded to refinish the surface.

Download the PDF version for printing

Make certain to keep your AK-47 clean and maintained so that information technology will last you lot a lifetime. The AK47 is still an awesomeweapon platform with many AK-47 Accessories bachelor to customize it for any need or use.